The F8 E6 error code is a drainage timeout issue  which signifies that the washer is unable to drain the water properly during the wash cycle within a specific timeframe set by the control board. This could be due to several reasons:

• Clogged drain pump or filter - The drain pump filter or hose might be clogged with debris like lint, coins, or buttons, preventing the water from draining out effectively.
• Faulty drain pump - The drain pump itself might be malfunctioning due to electrical problems, worn-out parts, or a blockage within the pump mechanism.
• Clogged drain hose - The hose that carries wastewater from the washer to the drainpipe might be clogged with debris or kinked, restricting water flow.
• Blocked drainpipe - The drainpipe itself, located in your house plumbing system, might be clogged with debris or a buildup of soap scum, preventing the washer's wastewater from draining properly.

The error code F8 E5 on a Kenmore washer indicates a problem with the hot and cold water fill hoses being reversed. This means the hoses supplying hot and cold water are connected to the incorrect valves on the washer.

Here's a breakdown of the explanation and troubleshooting steps

Issue - Reversed Hot and Cold Water Fill Hoses

When the hot and cold water hoses are reversed, the washer receives hot water instead of cold water during the rinse cycle, potentially leading to -

• Ineffective rinsing - Clothes might not be rinsed properly with hot water instead of cold.
• Color bleeding - Hot water can cause colors in fabrics to bleed or run, damaging clothes.
• Fabric damage - Hot water can damage delicate fabrics not meant to withstand high temperatures.

The error code F8 E3 on a Kenmore washer indicates an overflow fault, which means too much water is entering the washer. This can cause several problems, including:

• Water damage to the washer itself
• Mold or mildew growth
• Ineffective washing due to diluted cleaning solution

Here's a breakdown of the possible causes and troubleshooting steps for the F8 E3 error.

Possible Causes of F8 E3 Error

• Faulty water inlet valve - The valve that controls the water flow into the washer might be malfunctioning and not shutting off properly, leading to excessive water filling.
• Drain pump issue - A clogged drain pump or a malfunctioning drain pump itself could prevent proper water drainage, causing the washer to overfill.
• Pressure sensor problem - A faulty pressure sensor might be sending incorrect signals to the control board, causing it to believe the washer isn't full when it actually is, and leading to overfilling.
• Less likely (Control board issue) - In rare cases, the control board might be malfunctioning and sending incorrect signals to the water inlet valve, causing it to stay open too long.

Important safety precaution - Before attempting any troubleshooting steps, unplug the washer from the power outlet to avoid electrical hazards.

The error code F8 E2 on a Kenmore washer indicates a problem with the detergent dispenser system. This means the washer is detecting an issue that might prevent proper detergent dispensing during the wash cycle

Here's a breakdown of the possible causes and troubleshooting steps for the F8 E2 error

Possible Causes of F8 E2 Error

• Clogged detergent dispenser - The dispenser drawer itself or the compartments where detergent is poured might be clogged with accumulated detergent residue, fabric softener, or other debris. This can prevent the washer from properly dispensing the detergent into the wash water.
• Faulty dispenser - The detergent dispenser mechanism itself might be malfunctioning and unable to release the detergent properly.

The error code F8 E1 on a Kenmore washer indicates an issue with the washer's water filling system. It signifies that the washer is not detecting the correct amount of water entering the washer during a cycle. Here's a breakdown of the possible causes and troubleshooting steps.

Possible Causes of F8 E1 Error

• Water supply issue
  • Closed shut-off valves - The hot and/or cold water supply valves behind the washer might be closed, preventing water from entering.
  • Low water pressure - There might be insufficient water pressure coming from the house's main supply.
  • Clogged water inlet hoses - The hoses that connect the washer to the water supply might be clogged with debris, restricting water flow.
• Washer malfunction
  • Faulty water inlet valve - The valve that controls the water flow into the washer might be malfunctioning and not opening properly.
  • Faulty pressure sensor - The sensor that monitors the water level in the washer might be defective and sending incorrect signals to the control board.
  • Control board issue (less likely) - In rare cases, the control board might be malfunctioning and misinterpreting signals related to water filling.

The error code F7 E9 on a Kenmore washer indicates a problem with the washer's drain pump or the control board's communication with the pump. The drain pump is responsible for removing water from the washer during the rinse and spin cycles.

Here's a breakdown of the possible causes and troubleshooting steps for the F7 E9 error.

Possible Causes of F7 E9 Error

• Clogged drain pump - The drain pump filter or hose might be clogged with debris like lint, coins, or buttons, preventing the pump from functioning properly.
• Faulty drain pump - The drain pump itself might be malfunctioning due to electrical problems, worn-out parts, or a blockage within the pump mechanism.
• Loose electrical connections - Electrical connections between the drain pump and the control board might be loose or damaged, disrupting communication.
• Less likely (Control board issue) - In rare cases, the control board might be malfunctioning and unable to send proper signals to the drain pump.

The error code F7 E8 on a Kenmore washer signifies a communication error between the control board and another component, most likely related to the motor and its control.

Here's a breakdown of possible causes and troubleshooting steps

Possible Causes of F7 E8 Error

• Loose electrical connections - Electrical connections between the motor and the control board might be loose or damaged, disrupting communication. This is the most common cause of F7 E8.
• Faulty motor control board - The control board itself might be malfunctioning and unable to properly communicate with the motor.
• Less likely (Faulty motor) - In rare cases, the motor itself might be malfunctioning in a way that disrupts communication with the control board.

The error code F7 E7 on a Kenmore washer indicates a problem related to the washer's motor and its ability to reach the target RPM (revolutions per minute) during a wash cycle. 

Here's a breakdown of the possible causes and troubleshooting steps.

Possible Causes of F7 E7 Error

• Uneven load distribution - The washer basket might be overloaded or the clothes may be unevenly distributed, causing the motor to struggle and not reach the desired spin speed.
• Faulty motor - The motor itself might be malfunctioning due to worn-out brushes, internal problems, or overheating.
• Drive system issues - Components within the drive system, such as the belt, clutch, or transmission, might be faulty and hindering the motor's ability to reach the target RPM.
• Loose electrical connections - Electrical connections between the motor and the control board might be loose or damaged, disrupting communication and causing the error.
• Control board issue (less likely) - In rare cases, the control board might be misinterpreting signals from the motor and generating the error code.

The error code F7 E6 on a Kenmore washer indicates a problem with the washer's motor drive circuit or stator. The motor drive circuit is the electrical pathway that controls the washer's motor, and the stator is a key component within the motor itself. 

An F7 E6 error signifies the control board is detecting an issue that prevents the motor from functioning correctly. Here's a breakdown of the possible causes and troubleshooting steps for the F7 E6 error.

Possible Causes of F7 E6 Error

• Faulty stator - This is a common culprit. The stator itself might be malfunctioning due to internal electrical problems, overheating, or worn-out components.
• Motor drive circuit issue - Problems within the electrical pathway controlling the motor could be causing the error. This might involve faulty wiring, a malfunctioning component in the circuit, or a loose connection.
• Less likely (Control board issue) - In rare cases, the control board itself might be malfunctioning and sending incorrect signals to the motor drive circuit.

The error code F7 E5 on a Kenmore washer indicates a problem with the washer's drive system, specifically related to the shifter mechanism. The shifter is a component that engages different parts of the transmission to control the direction and speed of the wash basket during various wash cycles (agitation, spin, etc.). 

An F7 E5 error signifies the control board is detecting an issue with the shifter that prevents it from functioning properly. Here's a breakdown of the possible causes and troubleshooting steps for the F7 E5 error.

Possible Causes of F7 E5 Error

• Faulty shifter - The shifter itself might be malfunctioning and unable to properly engage gears or components within the transmission. This could be due to worn parts, mechanical failure, or debris jamming the mechanism.
• Loose electrical connections - Electrical connections between the shifter and the control board might be loose or damaged, disrupting communication. The control board relies on signals from the shifter to determine the wash basket's position and movement.
• Control board issue (less likely) - In rare cases, the control board might be misinterpreting signals from the shifter and generating the error code.